manuals/manuals_Support_Center_Ion_20Megatouch_20Wallette_20__20Entertainer_PM0491_03

merit entertainment

PM0491-03

MEGA-BRACKET INSTALLATION INSTRUCTIONS

PAGE 1 OF 2

BASE

ALLEN SCREW

EXTENSION ARM

MOUNTING HOLES

UPRIGHT SUPPORTS

CUT THIS END

DRILLED HOLE

LOCATIONS

ADJUSTABLE

CLAMPS

INSIDE ARM COVER

OUTSIDE ARM COVER

SCREWS

SECURING

ARM COVERS

Mega-Bracket Installation Instructions for Wallette and Entertainer Games

CONTENTS:

QTY PART

DESCRIPTION

1 SA0523-01

MEGA-BRACKET

BASE

SA0572-01

LEFT EXTENSION ARM ASSEMBLY

SA0572-02

RIGHT EXTENSION ARM ASSEMBLY

1 MP0083-01

LEFT

COVER

1 MP0083-02

RIGHT

COVER

HW9887-06

.22 ALLEN WRENCH

HW4553-04

¼ - 20 x 1” SOCKET-HEAD CAP SCREWS

4 HW5306-02

INTERNAL-TOOTH

LOCK

WASHER

HW4362-02

6 x 32 ¼” ONE-WAY SCREWS

1 HW9889-01

DRILL

BIT

HW2031-01 RUBBER GROMMET

NOTE: THIS INSTALLATION SHOULD ONLY BE PERFORMED BY A QUALIFIED SERVICE TECHNICIAN.

NOTE:

If you have installed the Premium Sound System, the game cannot be mounted using the

Mega-Bracket.

NOTE: Keep in mind that the bracket (4” H x 8” D) can accommodate a booth between 25” and
37” wide and there must be a straight edge on either side of the mounting surface. The booth
should be able to support the weight of the game and bracket and the tabletop must be between
1 1/8 and 2” thick to enable the adjustable clamps to grasp the edges. To ensure proper support,
the game should be placed against the wall of the booth.

1. Turn off and unplug the game.
2. Insert the extension arms into each end of the base and push the arms in until the adjustable clamps

are against each edge of the tabletop. See Figure 1.

FIGURE 1 - MEGA-BRACKET ASSEMBLY

merit entertainment

PM0491-03

MEGA-BRACKET INSTALLATION INSTRUCTIONS

PAGE 2 OF 2

3. Using the supplied Allen wrench, tighten both adjustable clamps so they are securely gripping the

tabletop. See Figure 1.

4. Slide the supplied covers over each arm as shown in Figure 1. The cover furthest from the base (the

outside cover) will slide under the inside cover. The outside cover will have to be cut to fit (see Figure
1). Allowing approximately one inch of the cover to overlap, cut any excess of the cover with a saw.

5. Using the supplied drill bit, and the hole in the inside cover as a guide, drill a hole through the outside

cover so that the holes in the overlapping covers line up. Repeat for the other side of the same cover
(see Figure 1). Then, fasten the covers using the 4 supplied one-way screws as shown in Figure 1.
The screws used in the drilled holes will only go through the covers, while the other screws will go
through the covers and the metalwork. Repeat this step for the covers on the other side.

6. Unlock and open the cash door.
7. The game can either be mounted with the upright supports located on the inside or outside the cash

door. If the back of the unit is against a wall, the supports should be on the outside so that the power
cord can be routed through the back of the cash door or through the openings at the bottom of the
base. If the back of the unit is not against a wall, the supports can be located inside the cash door. If
you are routing the power cord through the hole in the cash door, you must install the grommet in the
hole. To install, route the power cord through the grommet and then secure the grommet in the hole
in the plate (see Figure 2 for location).

FIGURE 2 - INSIDE VIEW OF WALLETTE / ENTERTAINER BACK PLATE

8. Fasten the game to the two upright supports by lining up the holes on the supports with those on the

back plate on the back of the game (see Figures 1 and 2). You may use any of the holes in order to
set the game to the desired height as long as the game is fastened with two of the supplied
1/4-20 x 1” socket-head cap screws and lock washers on each side.

9. Close and lock the cash door.

10. Plug in and turn on the game.

MOUNTING

HOLES FOR

FASTENING

BACK PLATE
TO UPRIGHT

SUPPORTS

(BOTH SIDES)

POWER CORD

ROUTING OPTION
(GROMMET MUST

BE INSTALLED)